RM新时代官方-首页

經常有一些車主在行駛中發現攪拌一體車機器轉向不穩，如果轉向不穩，應該檢查液壓泵和轉向器，找出以下原因：

Some owners often find that the steering of the mixer truck is unstable during driving. If the steering is unstable, check the hydraulic pump and steering gear to find out the following reasons:

1、轉向橫拉桿球銷、橫拉桿球銷磨損松動。由于斯太爾系列轎車的橫拉桿球銷和橫拉桿球銷沒有潤滑油嘴，出廠前已完全潤滑。風吹日曬雨淋，導致油脂減少、干燥、變質，導致潤滑性能差，導致球銷松動。目前，這種失效現象很多，由于材料和工藝問題，質量不穩定，磨損速度快。

1. The steering tie rod ball pin and tie rod ball pin are worn and loose. Since the tie rod ball pin and tie rod ball pin of Steyr series cars do not have lubricating nipples, they have been fully lubricated before leaving the factory. Wind, sun and rain have reduced, dried and deteriorated grease, resulting in poor lubrication performance and loose ball pins. At present, there are many such failures. Due to material and process problems, the quality is unstable and the wear speed is fast.

2、轉向節主銷和襯套的嚴重磨損和松動也是導致轉向不穩的原因。由于平時潤滑不足，主銷和襯套磨損大，轉向不穩是由于松動引起的。潤滑不足也會(huì )損壞主銷軸承。在正常的保養中，注意注入更多的潤滑脂，大部分油槍比較好。

2. The serious wear and looseness of steering knuckle kingpin and bushing are also the causes of unstable steering. Due to insufficient lubrication at ordinary times, the kingpin and bushing are greatly worn, and the unstable steering is caused by looseness. Insufficient lubrication can also damage the kingpin bearing. During normal maintenance, pay attention to inject more grease. Most oil guns are better.

3、前輪轂軸承松動。維修保養時應注意前輪轂軸承的潤滑，每次前輪轂軸承的安裝和壓蓋的緊固要適當。

3. The front hub bearing is loose. During maintenance, pay attention to the lubrication of the front hub bearing. Each time, the installation of the front hub bearing and the fastening of the gland shall be appropriate.

4、前橋的彎曲變形也會(huì )導致轉向不穩。由于行駛中片面追求效率，盲目超載，路面選擇不當，導致前橋彎曲變形。前軸彎曲變形過大，無法校正，必須更換。

4. Bending deformation of the front axle can also lead to unstable steering. Due to one-sided pursuit of efficiency during driving, blind overloading and improper selection of road surface, the front axle is bent and deformed. The front axle is too bent and deformed to be corrected and must be replaced.

5、攪拌一體車的車架和輪輞變形。

5. The frame and rim of the mixer truck are deformed.

6、轉向器內部零件磨損。舵機各部件的嚴重磨損也會(huì )導致轉向不穩的故障。應拆卸轉向機進行維修。合理裝載，中速行駛，盡量避免緊急制動，防止車架變形。車架變形也會(huì )導致轉向不穩定。

6. The internal parts of the steering gear are worn. Severe wear of steering gear components will also lead to unstable steering. The steering gear should be disassembled for maintenance. Load properly, drive at medium speed, and try to avoid emergency braking to prevent frame deformation. Deformation of the frame can also lead to unstable steering.

7、如果前束過大，方向盤會(huì )不穩，轉向也會(huì )不穩。前輪前束應保持在要求的范圍內。

7. If the toe in is too large, the steering wheel will be unstable and the steering will be unstable. Front wheel toe in shall be kept within the required range.

以上就是今天所要講解的內容了，相信大家在看完本文的描述之后，能夠對該產品有一定的認識和了解，希望以上內容能幫助到你。另外，若你想要了解更多相關資訊，可以多多關注我們的網站動態m.jackpetty.net。

The above is the content to be explained today. I believe that after reading the description of this article, you can have a certain understanding of the product. I hope the above content can help you. In addition, if you want to learn more about our website, you can pay more attention to our website at www.jfhntjbc com。