概述：使用前應做到Before use1、檢查各個水箱是否缺水并加足水，輪胎氣壓是否符合2 5bar以_上要求。1 Check whether each water tank is
使用前應做到
Before use
1、檢查各個水箱是否缺水并加足水，輪胎氣壓是否符合2.5bar以_上要求。
1. Check whether each water tank is short of water, add enough water, and whether the tire pressure meets 2.5bar_ The above requirements.
2、檢查發動機機油油尺，液壓油箱標尺，齒輪箱油標觀察孔，前、后橋，輪邊減速軸頭擰開油面油堵檢查齒輪油是否符合要求，缺少應及時添加，總泵自動液油杯液面是否合乎標準要求。
2. Check the engine oil dipstick, hydraulic oil tank dipstick, gearbox oil indicator observation hole, front and rear axles, wheel side reduction shaft head, unscrew the oil level oil plug, check whether the gear oil meets the requirements, add it in time if it is missing, and whether the liquid level of the automatic oil cup of the master cylinder meets the standard requirements.
3、觀測發動機機油，齒輪油，檢查油標尺，油標鑼孔，液壓油箱時，車輛要水平位置。
3. Observe the engine oil and gear oil, and check the oil dipstick, oil pointer, Gong hole and hydraulic oil tank. The vehicle shall be in a horizontal position.
4、全車各部油管路，氣管路接頭是松動有無漏油，漏氣現象。檢查全車線路有無接觸不良，各儀表，燈光是否工作正常。
4. The joints of oil and gas pipelines of all parts of the vehicle are loose, and whether there is oil and air leakage. Check whether the circuit of the whole vehicle has poor contact and whether all instruments and lights work normally.
生產的各操作閥的作用
Function of each operating valve produced
1、主車前后行走操縱閥( 快慢檔，前進和倒車檔)-般行走時為前駕，施工作業時為后駕。
1. The front and rear travel control valves of the main vehicle (fast and slow gears, forward and reverse gears) - generally, it is front drive during walking and rear drive during construction.
2、大臂升降旋轉操縱閥，舉料，左右旋轉罐體控制。
2. Boom lifting rotary control valve, material lifting, left and right rotating can body control.
3、料斗上下料操縱閥，鏟料、卸料控制鏟斗作用。
3. Hopper loading and unloading control valve, shovel and discharge control bucket function.
4、手動油門操縱閥，控制發動機的轉速，使攪罐在一定的平穩速度下旋轉。
4. The manual throttle control valve controls the engine speed to make the mixing tank rotate at a certain stable speed.
5、座椅腳踏定位卡銷，用于座椅調轉方向時起到鎖止作用，踏板踩向下時。鎖銷打開，左翼轉到位置后制動鎖止
5. The seat pedal positioning detent is used to lock the seat when turning the direction, and when the pedal is pressed down. The locking pin is opened and the brake is locked after the left wing is turned to the position
Today, Xiaobian presents you the relevant knowledge about automatic mixer truck. If you have any questions and questions about this article, please call us or leave a message below the website: http://m.jackpetty.net
點擊撥打服務熱線：4008791999
