RM新时代官方-首页

Where is the reason for the oil retaining failure of automatic feeding mixer?

如果使用時間過長，油封會(huì )磨損。方案：只需更換新的油封即可。

If used for too long, the oil seal will wear. Solution: just replace the oil seal with a new one.

如果長時間不更換機油，則濾芯的質量會(huì )下降，機油會(huì )變得太臟，加速油封的磨損。方案：盡快更換液壓油和濾芯。

If the oil is not changed for a long time, the quality of the filter element will decline, the oil will become too dirty, and the wear of the oil seal will be accelerated. Solution: replace the hydraulic oil and filter element as soon as possible.

主軸擺動油封磨損，因為驅動軸不平衡且劇烈振動。處理方案：及時糾正并更換軸。

The spindle swing oil seal is worn because the drive shaft is unbalanced and vibrates violently. Solution: correct and replace the shaft in time.

液壓油將變質并乳化，從而降低潤滑性能并加速油封的磨損。方案：盡快更換液壓油和濾芯。在嚴重的情況下，應清潔系統。

The hydraulic oil will deteriorate and emulsify, which will reduce the lubrication performance and accelerate the wear of the oil seal. Solution: replace the hydraulic oil and filter element as soon as possible. In severe cases, clean the system.

泵支架松動，泵打開，泵固定螺栓松動，導致整個液壓泵振動并磨損油封。方案：為防止和避免故障，請始終檢查并自上料攪拌車可能出現的故障。

The pump support is loose, the pump is opened, and the pump fixing bolts are loose, resulting in vibration of the whole hydraulic pump and wear of the oil seal. Solution: in order to prevent and avoid faults, please always check and eliminate possible faults of self loading mixer truck.

自動上料攪拌車系統的回油不暢，回油管和散熱器被堵塞，這會(huì )增加電機殼體中的壓力并導致油封泄漏。方案：堵塞物并穩定回油回路。

The oil return of the automatic feeding mixer system is not smooth, and the oil return pipe and radiator are blocked, which will increase the pressure in the motor housing and lead to oil seal leakage. Solution: remove the blockage and stabilize the oil return circuit.

如果散熱器不散熱，則油的溫度會(huì )過高，粘度和潤滑性會(huì )降低，油封會(huì )過熱，并且密封會(huì )失效。

If the radiator does not dissipate heat, the oil temperature will be too high, the viscosity and lubricity will be reduced, the oil seal will overheat and the seal will fail.

方案：散熱器上的障礙物并冷卻系統，以避免泵馬達磨損。在嚴重的情況下，有必要停止發動機，將其關閉，并用水沖洗泵馬達和散熱器殼體，以達到冷卻效果。

Solution: remove the obstacles on the radiator and cool the system to avoid wear of the pump motor. In severe cases, it is necessary to stop the engine, turn it off, and flush the pump motor and radiator housing with water to achieve cooling effect.

在冬季行駛時，由于預熱不足，油溫太低，并且油封和油封無法達到理想的工作溫度。對策：?jiǎn)?dòng)時，停止油箱，以怠速運行1020分鐘，并在油溫恢復正常后更換油箱。

When driving in winter, due to insufficient preheating, the oil temperature is too low, and the oil seal and oil seal cannot reach the ideal working temperature. Countermeasures: when starting, stop the oil tank, run at idle speed for 10 to 20 minutes, and replace the oil tank after the oil temperature returns to normal.

自動上料攪拌車液壓泵軸端的油封是易損件。嚴格遵守相關法規可以有效防止許多機油泄漏。如果遇到漏油問題，則需要冷靜下來，找出引起問題的具體原因。

The oil seal at the shaft end of the hydraulic pump of the automatic feeding mixer is a vulnerable part. Strict compliance with relevant laws and regulations can effectively prevent many oil leaks. If you encounter oil leakage, you need to calm down and find out the specific cause of the problem.

自動上料攪拌車擋油的問題就是這樣，你明白了嗎？

This is the problem of oil retaining of automatic feeding mixer truck. Do you understand?