概述: 1、攪拌一體車主機的潤滑檢查,在攪拌一體車主機運行時,可觀察潤滑脂泵刮油器是否在正常運轉的刮油?! ? Check the lubrication
1、攪拌一體車主機的潤滑檢查,在攪拌一體車主機運行時,可觀察潤滑脂泵刮油器是否在正常運轉的刮油。
1. Check the lubrication of the main engine of the mixer. When the main engine of the mixer is running, you can observe whether the grease pump scraper is in normal operation.
2、觀察潤滑脂泵壓力表的壓力值,正常情況下工作壓力為10bar---60bar,如壓力低于10bar,則可能為潤滑脂泵泵芯磨損或泵芯堵
2. Observe the pressure value of the grease pump pressure gauge. Under normal conditions, the working pressure is 10bar-60bar. If the pressure is lower than 10bar, the pump core of the grease pump may be worn or blocked
塞,如壓力高于60bar,則可能為分配閥堵塞或后面地管路堵塞。
Plug, if the pressure is higher than 60 bar, the distribution valve may be blocked or the pipeline behind it may be blocked.
?。?、在每個軸頭有一個備用黃油嘴,用手指甲壓下黃油嘴的頂珠,如有潤滑脂溢出,則證明軸頭潤滑到位,反之則證明軸頭潤滑不到位
3. There is a spare grease fitting on each shaft head. Press down the top bead of the grease fitting with fingernail. If grease overflows, it proves that the shaft head is lubricated in place; otherwise, it proves that the shaft head is not lubricated In place
4.風壓壓力在攪拌一體車主機運行的情況下正常值應為0.2----0.5bar,在攪拌拖泵一體機主機停止的情況下應為1---1,5bar,如超過或低于此兩值,應
4. The normal value of air pressure should be 0.2-0.5bar when the main engine of the mixing machine is running, and it should be 1-1,5bar when the main engine of the mixing and towing pump is stopped. If it is higher or lower than these two values, it should be
調整減壓閥壓力。
Adjust the pressure reducing valve.
5、攪拌一體車主機強電接線盒,保持密封,嚴禁用水沖洗。
5. The strong current junction box of the main engine of the mixing machine shall be sealed, and it is forbidden to wash it with water.
6、在自動生產狀態下,攪拌一體車主機卸料門手動手柄應處于收回位置,且球閥應處于中位,兩個手自動轉換螺堵應全部擰緊,避免手油
6. In the automatic production state, the manual handle of the discharge door of the main engine of the mixer should be in the retracted position, and the ball valve should be in the middle position. The two manual automatic transfer screw plugs should be tightened to avoid hand oil
泵過早損壞。
The pump failed prematurely.
7、攪拌一體車主機卸料門位置檢測開關與感應錐的間隙。
7. The clearance between the position detection switch of discharge door and the induction cone of the main machine of the mixer.
8、攪拌一體車主機減速箱應注意到加油和換油,檢查齒輪油是否充足,可以觀察其示油器的油位,在攪拌一體車主機停機狀態下,油位應在中位
8. Attention should be paid to oil filling and oil change for the reducer of the main engine of the mixer. Check whether the gear oil is sufficient. The oil level of the oil indicator can be observed. When the main engine of the mixer is stopped, the oil level should be in the middle
以上,即紅線以上。(齒輪油的牌號為美孚629?;驓づ疲保担埃?,用油量為16公升)另應經常檢查減速機運行是否平穩是否有噪音或異響。
Above, that is, above the red line. (the brand of gear oil is Mobil 629 or shell 150, and the oil consumption is 16 liters). In addition, it is necessary to check whether the reducer runs smoothly and whether there is noise or abnormal noise.