概述：攪拌車不經常檢測維護發動機會(huì )運轉狀態變差，增加燃料消耗，也容易產生積炭；平時應該養成經常檢查攪拌車空氣濾清器濾芯的習慣。 來了解下
攪拌車不經常檢測維護發動機會(huì )運轉狀態變差，增加燃料消耗，也容易產生積炭；平時應該養成經常檢查攪拌車空氣濾清器濾芯的習慣。 來了解下自動上料攪拌車吧：
If the mixer is not frequently inspected and maintained, the engine will run worse, increase fuel consumption, and easily produce carbon deposition; at ordinary times, the habit of frequently checking the air filter element of the mixer should be formed. Let's learn about the automatic feeding mixer
機油不能只靠加是要換 ，機油具有潤滑、冷卻、清潔等系列功用，一昧的加油不換油，容易形成各部件間的磨損，因此新的自動上料拌和車在運用500小時候需求換油，而后每1500小時換一次油，需求注意的是，駕駛員在替換時需求清洗油道，防止機械雜質留在油底殼及油路中。
The engine oil can't only be refilled, it needs to be changed The engine oil has a series of functions such as lubrication, cooling, cleaning, etc. it is easy to form wear between various parts if the oil is filled without changing. Therefore, the new automatic feeding mixer needs to change the oil when it is used for 500 hours, and then change the oil every 1500 hours. It should be noted that the driver needs to clean the oil passage when replacing to prevent mechanical impurities from remaining in the oil pan and oil circuit.
定期更換防凍液。防凍液長時間不換，其中的防腐、防銹和防垢功能將會(huì )降低，這樣會(huì )造成攪拌車冷卻系統故障甚發生銹蝕。一般來說，防凍液一般每1.5年-2年更換一次。
Change antifreeze regularly. If the antifreeze is not changed for a long time, its anti-corrosion, anti rust and anti scaling functions will be reduced, which will cause the failure of the mixer cooling system and even corrosion. Generally speaking, antifreeze is usually replaced every 1.5-2 years.
自動上料攪拌車制動性能的標準：
Safety standard for braking performance of automatic feeding mixer
自動上料攪拌車的制動性能的好壞與否，關系著攪拌機運行的性和效率，也關系到攪拌機機手的人身，所以必須定時的對攪拌機的制動性能做出準確的檢查，所以今天就看下自動上料攪拌車的標準是什么？
Whether the braking performance of automatic feeding mixer is good or not is related to the safety and efficiency of the mixer operation, and also related to the personal safety of the mixer operator. Therefore, the braking performance of the mixer must be checked regularly and accurately. So today, let's see what the standard of automatic feeding mixer is?
自動上料攪拌車制動系統應檢查制動性能是否處于良好狀態。在平直、干燥的水泥的平整路面上，攪拌車以24km/h速度行駛，用腳制動時，混凝土攪拌車的制動距離不大于9m?；炷翑嚢柢?chē)以30km/h速度行駛，點試制動，應迅速出現制動現象，且混凝土攪拌車不偏跑。
The braking system of automatic feeding mixer should check whether the braking performance is in good condition. On the flat, flat and dry cement road, when the mixer runs at the speed of 24km / h, and the foot brake is used, the braking distance of the concrete mixer is not more than 9m. When the concrete mixer runs at the speed of 30km / h, the braking phenomenon should appear quickly and the concrete mixer does not deviate.
基本檢查好以上幾點的的制動系統，就可正常使用了。
Basically check the above points of the brake system, it can be used normally.
點擊撥打服務熱線：4008791999
