自動上料攪拌車工作時應注意哪些問題
概述： 1、在施工現場卸料完畢后，應立即用攪拌車隨車的軟管沖洗進料斗、出料斗、卸料槽等，附著在車身上的污泥和混凝土?；爻虜嚢枵緯r(shí)，應
1、在施工現場卸料完畢后，應立即用攪拌車隨車的軟管沖洗進料斗、出料斗、卸料槽等，附著在車身上的污泥和混凝土?；爻虜嚢枵緯r(shí)，應向攪拌筒內注入150—200L的水，與葉片粘結的筒壁和混凝土殘留物。
1、After the unloading is completed at the construction site, the hose of the mixer car shall be immediately used to wash the inlet hopper, outlet hopper, unloading trough, etc., and the sludge and concrete attached to the car body shall be removed. Return mixing station should be fill 150-200L of water in the mixing drum to remove the wall and concrete residues bonded with the blades.
2、每天工作結束后，駕駛員應負責向攪拌筒內注入清水，并以高速(14-18轉/分)旋轉5—10分鐘，然后排出水流，保證筒體清潔。當使用高壓水清洗攪拌筒的各部分時，要注意避開儀器、操縱桿等部位。水口與車體漆面之間的距離不得小于40厘米。
2、At the end of each working day, the driver shall inject clear water into the mixing drum, rotate it at high speed (14-18 rpm) for 5- 10 minutes, and then discharge the water to ensure the cleaning of the drum. When the use of high-pressure water cleaning mixing drum of the various parts, we should pay attention to avoid the instrument, joystick and other parts. The distance between the nozzle and the body paint shall be no less than 40 cm.
3、當維修人員進入攪拌筒內進行檢修和補焊作業時，應先將攪拌筒內外的污物及殘留的混凝土渣塊，使攪拌筒完全停止轉動。技工進入筒體時，應保證攪拌筒內的通風良好，空氣新鮮，無然氣體和有害粉塵，氧氣供應充足。使用電動工具操作筒時，操作者必須有良好的絕緣保護。
3、When the maintenance personnel enter the mixing drum for overhaul and repair welding, the dirt inside and outside the mixing drum and the remaining concrete slag shall be cleared first so as to make the mixing drum stop turning completely. Technicians into the cylinder, should ensure that the mixing drum of good ventilation, fresh air, no natural gas and harmful dust, oxygen supply is sufficient. When using the power tool operating barrel, the operator must have good insulation protection.
4、工作時，不得將手伸入旋轉攪拌筒內，不能將手伸入主卸料溜槽與加長卸料溜槽的連接處，自動上料攪拌車在工作時應注意哪些問題，以免發生意外。
4、When working, shall not put hands into the rotating mixing drum, shall not put hands into the joint of the main unloading chute and the extended unloading chute, and shall pay attention to what problems should be paid to when the automatic charging and mixing truck works to avoid accidents.
點擊撥打服務熱線：4008791999
