RM新时代官方-首页

　　自動上料攪拌車作為大型施工設備，往往在施工期間伴隨著問題的出現，所以提前掌握相關的問題內容很重要，下面通過五大快問快答來了解了解。

　　As a large construction equipment, automatic feeding mixer is often accompanied by problems during construction, so it is important to master the relevant problems in advance. The following five quick questions and answers are used to understand.

　　開自動上料攪拌車應該注意什么？

　　開自動上料攪拌車，對有經驗的駕駛員來說，一般的駕駛常識都會。在此要提醒的是，由于混凝土是流態的，在車輛急轉彎的時候要降低速度，以免混凝土轉彎時產生的離心力使車輛不穩！

　　What should be paid attention to when driving an automatic feeding mixer?

　　Open automatic feeding mixer, for experienced drivers, the general sense of safe driving will. Here to remind is, because the concrete is flow state, in the vehicle when the sharp turn to reduce speed, so as to avoid the concrete turn when the centrifugal force to make the vehicle instability!

　　混凝土凝固在攪拌車?yán)镌趺崔k？

　　混凝土凝固后，其主要成分是硅酸二鈣、硅酸三鈣。理論上講，鹽酸可以與之反應解除其固態形狀。但實際上很難操作，因?yàn)閿嚢柢嚨牧峡诤苄。}酸量難以控制，且鹽酸也可以與攪拌車罐體發生反應。實際出現這種情況，往往是用電焊或氣割切開罐體，然后將凝固的混凝土機械破碎。

　　What if the concrete solidifies in the mixer?

　　After solidification of concrete, its main components are dicalcium silicate and tricalcium silicate. Theoretically, hydrochloric acid can react with it to remove its solid shape. But in practice it is difficult to operate, because the blender mouth is small, the amount of hydrochloric acid is difficult to control, and hydrochloric acid can also react with the mixer tank. The actual occurrence of this situation, often with electric welding or gas cutting cut tank body, and then the solidification of the concrete mechanical broken.

　　攪拌車上裝指的是什么？

　　攪拌車上裝指的是攪拌車除底盤擋泥板以外的東西，包括攪拌罐體及支座，進出料斗，液壓系統及減速器，水箱及管路，操作連桿機構等。

　　What does the mixer truck mean?

　　The stirring car refers to the stirring car in addition to the chassis fender things, including mixing tank and support, in and out of the hopper, hydraulic system and reducer, water tank and pipeline, operating connecting rod mechanism.

　　攪拌車的焊接工藝是怎樣的？

　　現在一般廠家都對整個車子的焊接采用全自動無縫焊接，環縫和縱縫均采用全自動無縫焊接。

　　What is the welding process of agitator truck?

　　Now the general manufacturers of the whole car welding using automatic seamless welding, circular seam and longitudinal seam are using automatic seamless welding.

　　How to do with the laborious discharging of the automatic feeding agitator? Have better method besides adding water?

　　自動上料攪拌車出料費勁怎么辦？除加水外有無更好辦法？

　　如果是因?yàn)榛炷恋脑颍蔷鸵纯词翘涠忍∵€是混凝土強度太高，還是混凝土太黏不好下的原因，以上原因可根據施工要求適當調整一下混凝土；如果總是不好下，就要考慮是否葉片角度和下料口那塊有問題。

　　If it is because of concrete, it is necessary to see whether the slump is too small or the strength of concrete is too high, or the concrete is too sticky under the reasons, the above reasons can be adjusted according to the construction requirements of concrete; If it is always not good, it is necessary to consider whether there is a problem with the blade Angle and the feeding port.

　　更多內容您可以來網站m.jackpetty.net咨詢，有關人員會為您做好詳細的解答！

　　More content you can come to the website m.jackpetty.net consultation, relevant personnel will do a detailed answer for you!