RM新时代官方-首页

自動上料攪拌車易損傷部位有哪些呢？易損傷部位主要是指攪拌車上使用頻率較高的零部件，比如液壓系統，托輪，滾道，水箱，發動機等等部位。

What are the vulnerable parts of the automatic feeding mixer? The easily damaged parts mainly refer to the frequently used parts on the mixer, such as hydraulic system, carrier wheel, raceway, water tank, engine, etc.

我們都知道自動上料攪拌車在行駛過程中罐體是一直轉動的，這樣才能保證罐內的混凝土不凝固，不離析，罐體的轉動離不開托輪和滾道，這兩個部位一旦出問題就會造成非常嚴重的后果——混凝土凝結。所以這兩個部位的保養是長久性的，托輪和滾道之間要經常涂抹潤滑油，對于滾道上的污物要及時清理，以免影響罐體轉動。

We all know that the tank body of the automatic feeding mixer rotates all the time during driving, so as to ensure that the concrete in the tank does not solidify and segregate. The rotation of the tank body cannot be separated from the supporting wheel and the raceway. Once there is a problem with these two parts, it will cause very serious consequences - concrete condensation. Therefore, the maintenance of these two parts is permanent. Lubricant should be applied frequently between the supporting roller and the raceway. The dirt on the raceway should be cleaned in time to avoid affecting the rotation of the tank.

自動上料攪拌車上的液壓系統也是非常重要的，攪拌罐側操作主要是依靠液壓系統來實現的，它的保養也是關重要的，比如液壓油要定期更換，不要使用劣質液壓油，對于液壓軟件要經常檢查，潤滑度不夠的要及時添加潤滑油脂，如有損傷元件要及時更換，保證液壓系統的靈活使用。

The hydraulic system on the automatic feeding mixer is also very important. The operation on the side of the mixing tank is mainly realized by the hydraulic system, and its maintenance is also crucial. For example, the hydraulic oil should be replaced regularly, and the low-quality hydraulic oil should not be used. The hydraulic software should be checked frequently. If the lubrication is not enough, the lubricating grease should be added in time. If there are damaged components, they should be replaced in time to ensure the flexible use of the hydraulic system.

自動上料攪拌車上水箱的大小及安裝部位都是廠家經過設計師的精心設計的，所以不要隨意的改動，水箱的視水管和過濾網偶爾也要查看一下，視情況更換，以免引起堵塞，影響水位的判斷，在冬天工作完成后要及時的將水箱內的水排出，以免結冰引起水箱開裂。

The size and installation position of the water tank on the automatic feeding mixer are carefully designed by the manufacturer, so do not change them at will. The water pipe and filter screen of the water tank should be checked occasionally and replaced as appropriate to avoid blockage and affect the judgment of water level. After the work is completed in winter, the water in the water tank should be drained in time to prevent the water tank from cracking due to icing.

發動機的使用也是非常多的，所以對發動機的保養也要注意，尤其是機油，要經常查看機油，發現機油變質要及時更換，油量變少要及時添加。對于新買的自動上料攪拌車要注意螺栓，因為新車在使用一段時間后各部位的螺栓容易松動，所以在使用的過程中要十分注意，發現松動螺栓及時緊固；新車的行駛速度不易過快也不易過慢，要按規定的時間進行保養。

The engine is also used very much, so we should pay attention to the maintenance of the engine, especially the engine oil. We should check the engine oil frequently. If the engine oil is deteriorated, we should replace it in time, and if the oil quantity becomes less, we should add it in time. Pay attention to the bolts of the newly purchased automatic feeding mixer, because the bolts of each part of the new car are easy to loosen after using for a period of time, so pay great attention during the use process, and tighten the loose bolts in time; The driving speed of a new car is not easy to be too fast or too slow, and maintenance should be carried out according to the specified time.

自動上料攪拌車是建筑工程上主要的專用車型，保養是非常重要的，尤其是使用比較頻繁的零部件，保養好了才能增加攪拌車的使用壽命，您還有什么要點沒了解到可以隨時來聯系我們http://m.jackpetty.net！

The automatic feeding mixer is a major special vehicle for construction projects. Maintenance is very important, especially for parts that are frequently used. The service life of the mixer can be increased only after the maintenance is completed. If you don't know any important points, please contact us at any time http://m.jackpetty.net ！