RM新时代官方-首页

The automatic mixer may stop running suddenly in the process of working, which will not only affect the quality of concrete, but also delay the progress of the project, and bring great trouble to users. So what should we do when the automatic mixer stops working suddenly?

1.調整機器負荷

1. Adjust the machine load

自動攪拌車如果超過正常負荷工作，會使攪拌軸轉動緩慢，若負荷過大，就會導致攪拌軸停轉或者是攪拌軸彎曲，這時只需調整進料量，卸出多余的物料，降低攪拌軸轉動負荷即可。

If the automatic mixer works beyond the normal load, it will make the mixing shaft rotate slowly. If the load is too large, it will cause the mixing shaft to stop or the mixing shaft to bend. At this time, it is only necessary to adjust the feed volume, unload the excess material and reduce the rotating load of the mixing shaft.
            

2.異物

2. Remove foreign matters

當自動攪拌車的攪拌葉片或側葉片與罐內壁間有較大的異物，尤其是石子，也會導致攪拌軸停轉，之所以能卡存異物，就是自動攪拌車的攪拌葉片或側葉片與罐內壁間隙過大造成的。側葉片與關內壁卡滯物料時，在攪拌軸停轉前往往會有尖銳刺耳的摩擦聲，出現這種情況時，需立即停機檢查，人工排除異物，重新調整自動攪拌車的葉片或側葉片與罐內壁間的間隙，有必要時可以用水先清洗下。

When there are large foreign matters, especially stones, between the mixing blade or side blade of the automatic mixer and the inner wall of the tank, it will also cause the mixing shaft to stop. The reason why the foreign matters can be trapped is that the gap between the mixing blade or side blade of the automatic mixer and the inner wall of the tank is too large. When the material is stuck between the side blade and the inner wall, there will be sharp and harsh friction sound before the mixing shaft stops. In this case, it is necessary to stop the machine immediately for inspection, manually remove foreign matters, readjust the gap between the blade of the automatic mixer or between the side blade and the inner wall of the tank, and clean it with water if necessary.

3.張緊電機傳動皮帶

3. Tighten the motor drive belt

自動攪拌車電機傳動皮帶過松也能導致自動攪拌車的攪拌軸轉動緩慢或者停止轉動，這是因為電機傳動皮帶過松，導致傳遞的動力不足。此時只需停機后調整自動攪拌車電機傳動皮帶的張緊度即可。

The motor drive belt of the automatic mixer is too loose, which can also cause the mixing shaft of the automatic mixer to rotate slowly or stop rotating. This is because the motor drive belt is too loose, which leads to the lack of power transmission. At this point, it is necessary to adjust the tension of the motor belt of the automatic mixer after stopping the machine.

自動攪拌車在日常使用過程中用戶要注意維修保養，能夠提前的問題就及時，不要因小失大，影響整個工作進度。

In the process of daily use of automatic mixer, users should pay attention to maintenance, and solve the problems that can be solved in advance, so as not to affect the whole work progress.